Views: 0 Author: Site Editor Publish Time: 2026-11-18 Origin: Site
As temperatures gradually drop, whether it's freezing conditions in northern regions or sudden temperature fluctuations in southern areas, winter weather can put welding equipment in workshops to the test. Many operators assume that only workshops in freezing northern climates need to prepare their welding machines for winter. In fact, this is not the case.
Low-temperature freezing, condensation caused by temperature changes, static electricity in dry environments, and dust accumulation that blocks cooling systems are all potential problems in manufacturing workshops across different regions.
As a professional welding equipment manufacturer in China, PDKJ has put together a practical winter maintenance guide for users worldwide. This guide covers the key maintenance requirements for different machine types, including both water-cooled and air-cooled handheld laser welding machines. The procedures are straightforward and easy to implement.
For handheld laser welding machines equipped with water-cooling systems, the cooling circuit is essential to stable equipment operation. When the average daily temperature at the installation site drops below 5°C (41°F), preventive measures against freezing should be taken in advance.
Once the cooling water freezes, its volume expands, potentially cracking water pipes, pumps, and filters. Such freeze-related damage is generally not covered by standard warranty policies. Taking preventive measures in advance can help avoid costly repairs and production downtime.
Whenever possible, maintain the temperature in the equipment operating and storage areas above 5°C (41°F).
When the machine is shut down overnight and left unattended, avoid placing it near doors, windows, or other locations directly exposed to cold drafts to minimize the impact of low temperatures.
If the factory has a stable power supply, the chiller can be kept running continuously at a low load.
Set the cooling water temperature to approximately 5°C (41°F) to help keep the coolant above its freezing point and prevent it from freezing during periods of inactivity.
After completing daily operations and shutting down the machine, open the drain valve and completely remove any remaining cooling water from the laser source and chiller.
If conditions permit, a circulation cycle using antifreeze can also be performed to provide additional protection for the cooling circuit.
If the equipment will remain unused for an extended period or needs to be transported to a low-temperature worksite in northern regions, the coolant should be replaced with a dedicated antifreeze solution.
When selecting antifreeze, make sure its freezing point is lower than the historical minimum temperature of the local area. A higher antifreeze concentration does not necessarily mean better protection.
Important Reminder About Antifreeze
Antifreeze should not completely replace deionized water for long-term use.
Once temperatures rise and the winter season has passed, thoroughly flush the entire cooling circuit with distilled or deionized water and replace the antifreeze with the recommended standard coolant. This helps prevent long-term corrosion, impurity buildup, and potential blockages in the cooling circuit.
After powering on the equipment, start the water circulation system first and allow it to preheat.
Wait until the water temperature stabilizes between 20°C and 28°C (68°F–82°F) before beginning welding operations.
This helps maintain consistent welding performance while providing better protection for the laser source and its core components.
Integrated air-cooled laser welding machines do not have a water-cooling circuit, so there is no risk of cooling pipes freezing and cracking.
However, they still face several common winter-related risks: dust accumulation blocking air ducts, static electricity building up in dry environments, and internal condensation caused by temperature fluctuations.
These are among the main causes of winter-related equipment failures in air-cooled laser welding machines.
The air intake filter is the first line of defense for an air-cooled cooling system.
Once blocked by welding spatter, metal dust, or other debris, airflow decreases and cooling efficiency drops significantly. This can easily trigger over-temperature protection and cause the machine to shut down.
Recommended maintenance practices:
Establish a regular cleaning schedule. For workshops with heavy dust exposure, clean the air intake filter at least once a week.
Use dry compressed air to blow dust from the inside outward, or gently clean the filter with a soft brush.
Avoid applying excessive force to prevent damage to the filter.
For workstations with frequent welding spatter, keep the machine's air intake away from the spatter area whenever possible.
When the machine is not used for an extended period, cover it with a dust cover.
Static electricity is more likely to accumulate in dry air.
When static electricity builds up on circuit boards or optical components, it may contaminate optical lenses and cause unstable laser output. In more serious cases, electrostatic discharge can damage sensitive electronic components, resulting in irreversible failures.
Practical precautions:
Ensure that the welding machine is properly and reliably grounded.
Before maintenance or touching optical lenses and circuit boards, discharge static electricity by touching a grounded metal surface.
Maintain workshop humidity between 40% and 60% whenever possible. This helps reduce static electricity while avoiding excessive humidity that could cause condensation.
Operators should wear anti-static wrist straps when conditions permit, especially when handling sensitive electronic or optical components.
If the equipment is moved from a cold warehouse or outdoor environment into a warm workshop, do not power it on immediately.
Significant temperature differences can cause moisture to condense inside the machine and on optical lenses. Powering on the equipment before the condensation has disappeared may create a risk of electrical short circuits.
Allow the machine to stand for an appropriate period until the entire unit reaches room temperature and internal moisture has completely evaporated before connecting it to the power supply.
Air-cooled laser welding machines rely on fans for heat dissipation. Never cover or wrap the machine during operation, as this will restrict airflow and may cause overheating.
Optical lenses are essentially the "eyes" of a laser welding machine.
Under low temperatures and changing environmental conditions, condensation can easily form on optical lenses. Many problems, such as difficulty initiating the laser arc and unstable laser spots, may actually originate from contaminated or fogged lenses.
Follow these maintenance procedures:
1. Routine Inspection Before Startup
Before starting work each day, carefully inspect the protective lens and focusing lens. Check for condensation, water stains, dust, and other contaminants on the surfaces.
2. Proper Lens Cleaning
If condensation or contamination is detected, use a lint-free cotton swab lightly moistened with anhydrous alcohol.
Gently wipe the lens in one direction only. Make sure the surface is completely dry and free of residue before using the equipment again.
3. Critical Safety Precaution
Never activate the laser if there is still condensation on the optical lens.
Doing so can easily cause permanent damage or burn-through of the lens.
Good equipment performance depends not only on the machine itself, but also on proper operation and regular maintenance.
To keep welding machines operating reliably throughout the year, seasonal maintenance is essential.
As a professional welding equipment manufacturer, PDKJ understands the importance of equipment reliability for users working under different operating conditions and climates around the world.
Our goal is to ensure that every welding machine leaving our factory can deliver stable performance, minimize unexpected downtime, and support efficient production.
If you encounter any difficulties during equipment maintenance, adjustment, or operation, feel free to contact our technical support team.
With colder weather approaching, take preventive measures in advance to keep your welding equipment running smoothly throughout the winter and ensure more efficient welding operations.
|
|
If you have welding machine requirements, please contact Ms. Zhao
E-Mail: pdkj@gd-pw.com
Phone: +86-13631765713